Cat Cams camshaft for Renault J6 / J7 8V engine
Brand : Cat Cams
Condition : New
Model : Renault J6 / J7 8V
Product : Camshaft
For Renault J6 / J7 8 valve SOHC engines. Select the profile to suit the intended use and engine management. Profile G is only for a suitably prepared conversion from a naturally aspirated to a turbocharged engine.
| Profile | Duration at 0.1 mm intake / exhaust | Duration at 1 mm intake / exhaust | Valve lift intake / exhaust | Lift at TDC intake / exhaust |
|---|---|---|---|---|
| Profile A | 260 / 260° | 223 / 223° | 9.35 / 9.35 mm | 1.30 / 1.30 mm |
| Profile B | 268 / 268° | 230 / 230° | 9.65 / 9.65 mm | 1.65 / 1.65 mm |
| Profile C | 291 / 291° | 251 / 251° | 11.65 / 11.65 mm | 2.90 / 2.90 mm |
| Profile D | 309 / 309° | 264 / 264° | 11.90 / 11.90 mm | 3.85 / 3.85 mm |
| Profile E | 318 / 318° | 273 / 273° | 12.50 / 12.50 mm | 4.55 / 4.55 mm |
| Profile F | 323 / 323° | 282 / 282° | 12.90 / 12.90 mm | 5.10 / 5.10 mm |
| Profile G | 291 / 291° | 251 / 251° | 11.65 / 11.65 mm | 2.90 / 1.95 mm |
Profile A : Manufacturer exterior spring configuration: original, subject to checks.
Profile B : Manufacturer exterior spring configuration: original, subject to checks.
Profile C : Manufacturer exterior spring configuration: specific springs, not stated as supplied with the camshaft. Competition applications only. Only for dirt track and prepared applications with adjustable engine management or carburettors. The manufacturer requires an additional spacer under the lower retainer to achieve the correct fitted length, approximately 3 mm; check the final dimension on the engine. At least 0.6 mm between valve seal and retainer at full lift.
Profile D : Manufacturer exterior spring configuration: specific springs, not stated as supplied with the camshaft. Competition applications only. Independent engine management with a throttle position sensor or carburettors is required. The manufacturer requires an additional spacer under the lower retainer to achieve the correct fitted length, approximately 3 mm; check the final dimension on the engine. At least 0.6 mm between valve seal and retainer at full lift.
Profile E : Manufacturer exterior spring configuration: specific springs, not stated as supplied with the camshaft. Competition applications only. Independent engine management with a throttle position sensor or carburettors is required. The manufacturer requires an additional spacer under the lower retainer to achieve the correct fitted length, approximately 3 mm; check the final dimension on the engine. At least 0.6 mm between valve seal and retainer at full lift.
Profile F : Manufacturer exterior spring configuration: specific springs, not stated as supplied with the camshaft. Competition applications only. Independent engine management with a throttle position sensor or carburettors is required. The manufacturer requires an additional spacer under the lower retainer to achieve the correct fitted length, approximately 3 mm; check the final dimension on the engine. At least 0.6 mm between valve seal and retainer at full lift.
Profile G : Manufacturer exterior spring configuration: specific springs, not stated as supplied with the camshaft. Competition applications only. Independent engine management with a throttle position sensor or carburettors is required. The manufacturer requires an additional spacer under the lower retainer to achieve the correct fitted length, approximately 3 mm; check the final dimension on the engine. At least 0.6 mm between valve seal and retainer at full lift.
Camshafts must turn freely in the head, with machining where necessary; at least 0.6 mm between valve seal and retainer at full lift; at least 1 mm of remaining spring travel; at least 1 mm valve to piston clearance, preferably 1.5 mm. Check 5 to 15° before TDC on the exhaust and after TDC on the intake.
The figures and restrictions below are provided by the manufacturer. A professional must install and time the camshafts after checking the valve train, clearances, springs and engine management compatibility. Performance preparation part, with no claimed power gain or road approval. Manufacturer information for original springs and components does not replace mechanical checks. Image for reference only; no additional accessories are specified.
-
Brand
-
ReferenceSASAC0006-A
-
VehiclesRenault J6 / J7 8V